Canvas Printing

-

Ever since I made my version of one of Sam Lauren Smiths inky drawings, it has been stuck to our kitchen wall, waiting for me to get a much bigger laser so I could cut one at the size I wanted it (1.2m long). The more I looked at it the less I liked the burnt wood on wood effect until finally one day I decided that I should just go ahead and get a proper black and white canvas job done. I contacted the artist again but still didn't hear anything so I went ahead and used my own scanned images of the postcard.

This is where Chris Braunston of Braunston Ltd printing company comes in. He's my guru for all things print related and he's help me make custom Tshirts and vinyl Wall stickers before. They do canvas printing and were happy for me to go down and watch/help the whole process.


A big print job requires a big printer and this one prints directly to the canvas. It was fairly straight forward, a program adds some margin around the edge of the image to wrap around the block (particularly helpful in this case as the image has it's own white margin). It also adds some alignment marks on the very edges because most of the time the image is face down. 



The print was cut off the roll and trimmed down ready to be put on the frame. The frame typically started life as 4 planks of wood. The four planks were cut to size with 4 degree angles on the corners. The shed is a great idea, you don't want to get sawdust all over the office so Chris installed an actual shed in the car park. Some beefy staples were gunned in at the corner leaving me a little sceptical but after looking at the frame it really was solid. The frame was then ready for the canvas. 


Wrapping the canvas round the frame is when the real skill comes in. Knowing how to fold the corners is a great start. The canvas is cut into the corner, folded as shown and then stapled down, a matching 45 degree fold is made on the remaining tab and that side is (eventually) stapled down too. The tensioning tool is the specialised tool on the job and it definitely made things easier. They're like a pair of pliers which grip the canvas but they have an extra bump which allows can be levered against the frame to pull the canvas type, another staple keeps it tight. That's about it, a dozen staples all round the frame keep everything in place and the canvas print is done (and looks amazing)


When I got it home I set about hanging it straight away. The intention was to put two nails into the wall and hang the frame up on them. I made sure they were level and hung the picture but it just didn't look straight. Turns out our ceiling isn't level and the canvas just didn't look right until the two lines were parallel. I should put some wire on the back to allow for that kind of adjustment but I'll need to go out and buy that. In the meantime I laser cut a doughnut to go over the nail, lifting the right hand edge by 15mm and making it all appear level. Let's face it it just wouldn't feel right if one of my projects didn't have a laser cut part in it somewhere.





Popular posts from this blog

Wiring the Ruida Controller

-
Image
The RDC6442G controller from Ruida This is going to be quite an image heavy post describing the rewiring needed to convert between the Leetro controller and the Ruida controller. It is also pretty straight forward on the old Just Add Sharks laser cutters because all of the wires are clearly labelled. The controller was prepared in the previous step in order to make this conversion process as smooth as possible. The Leetro (Pad03) panel on the left and the Ruida panel on the right The view from inside the laser looking up at the control panel The control panel is an easy place to start, both panels have just a single cable that runs down to the controller, both panels are a very similar size, with the Ruida panel being slightly smaller underneath so it will fit in the hole left behind easily. The Pad03 panel clips into place so you'll need to reach up inside the machine to work the clips loose. The cable runs down the inside of the laser and is cable tied onto mounti
Read more

Rainbow Puzzle Box

-
Image
This is a binary sequence puzzle box built from 3mm birch plywood, it uses a Gray code pattern to ultimately align all the dials into a rainbow pattern before the lid can be removed. It's actually a redesign of a puzzle inside Loki's box of Tricks  because I thought it would make a cool stand alone puzzle box. The files are available for sale in my Etsy store . ( svg here ) The puzzle consists of five interlocking disks that can only rotate when the disks either side of it are in the correct position to allow it. The large wheel in the middle and the disks on the underside of the lid further restrict the rotation of the disks. The large wheel must be pointed to the disk that is being rotated and the large wheel is in turn restricted from pointing to the smaller disks depending on alignment. Once all the disks are aligned into the full rainbow the large wheel is completely free to rotate and can be turned to the edge of the box and allows the lid to be removed. There is a very
Read more

Laser Cut Cryptex

-
Image
This is my laser cut cryptex. It features 28 different characters and 9 rings, giving a total possible 10.5 Trillion different combinations. I took a bit of time developing the design so that I could add some nice features. This cryptex file is laid out so that you can have any number of rings in your own design. The best feature is that the codeword is changeable, each locking ring has an outer letter ring that can be placed in any one of the 28 different positions. Once the rings are back in place the ring locking bars can added and they prevent the rings from being modified until the box is open again. It's a bit hard to explain so I made a video showing how it all work ( svg here ) It took a long time to assemble this so I lived with my initial design choices but if I were to remake it I would adjust the file to make the ring locking bars out of 6mm ply and maybe put some blind holes onto the code rings to prevent the code being brute forced.
Read more